One (1) Frame-9E (PG9171E) gas turbine which is characterized by the following equipment and accessories except where mentioned otherwise.

Performance Specifications

    Power Rating at Generator Terminals (ISO, Natural Gas)

        Output:                    123.4 MW

        Voltage:                   11.5 kV

        Frequency:              50 Hz

        P.F.                            0.85

        Heat Rate (LHV):    10660 kJ/kWh

        Pressure Ratio:        12.6

        Mass Flow:              405 kg/s

        Firing Temp.:           1,124 °C

        Exhaust Temp.:        543 °C

        Shaft Speed:            3000 RPM

1.  Turbine and Turbine Compartment

Base mounted, simple cycle, single shaft PG9171E Gas Turbine Compartment consisting of:

·   Multistage, axial flow corrosion protected compressor.

·   Fourteen chamber combustion system.

·   3-stage turbine with coated first stage buckets.

    Modulating inlet guide vanes of C450 material.

·   On base Gas fuel system and Liquid fuel system suitable for distillate.

·   Dual ignition system.

·   Dual compartment AC vent fans (Negative, common for GT & ACC compartment),

·   Vibration sensors. Seismic type, for protection.

·   Thermocouples for measuring critical turbine and load temperatures, including bearing drains.

·   Inlet and exhaust plenums.

·   Load coupling (solid) with coupling guard and hardware.

·   GT enclosure (On-base) limiting near field noise level to 93 dBA.

·   Oil filled accessory coupling.

·   Fire detection and protection for on-base equipment.

·   On line and Off line compressor wash piping and nozzles for on-base hardware.

·   Compressor discharge air unit. On-base piping as per ANSI B31.3

·   Base mounted terminal boxes and interconnecting wiring in rigid metal conduits.

2.  Accessory Systems and Compartment

Accessory systems and compartments include:

·   Accessory gear, heavy duty, multi shaft with oil filled accessory coupling to turbine shaft.

·   Starting system

·   Electric motor

·   Torque converter

·   Rotor turning device

·   Fuel oil pump

·   Lubricating and hydraulic oil system.

·   Shaft driven main lubricating oil and hydraulic oil pumps

·   Full flow AC Motor driven auxiliary pump

·   Partial flow AC Motor driven emergency pump

·   Full flow AC Motor driven auxiliary hydraulic pump

·   Dual filters and transfer valve for lubricating oil and hydraulic oil systems

·   2 X 100% lube oil to water heat exchangers

·   304/321 Stainless steel feed piping with TIG welding of foot pass

·   Piping in accordance with ANSI B31.3 and applicable ASME welding requirement

·   Fire detection and CO2 protection system for on-base equipment, Electrical components,

·   All motors, except starting motor, feature:

·       TEFC motors, Terminal boxes, conduit and wiring to meet NCC Class-1, Group--D, Division-2.

·       Dual compartment vent fans (negative ventilation common for ACC & GT compartments.

·   Full weather protected enclosure for outdoor installation.

3. Inlet Air System (Up & Over Orientation)

·   Filter compartment with:

·   Support structure

·   Self cleaning air filter system

·   Inlet ducting

·   Access hatch

·   Instrumentation

·   Inlet silencing in ducting.

·   Inlet bellow.

·   Transition piece from inlet ducting to inlet plenum.

·   Structural supports

4.  Exhaust System (Top Exhaust)

·   Transition piece and stack of 15 meters height, including silencer,

5.  Load Coupling Compartment

·   Rigid non-lubricating load coupling.

·   Fabricated toad coupling guard.

·   Full weather protected enclosure.

6.  Following Equipment Will Be Supplied To Be Mounted In Local Control Cabinet

·   Mark V Speedtronic TM turbine control panel.

·   Motor Control Center. 125V DC Battery (Lead maintenance free) Charger and DCDB.

7.  Auxiliary Compartments & Turbine Fire Detection and Protection System (CO2)

8.  Portable Lube Oil Purifier

9.  Foundation Hardware

10. Special Tools and Tackle (One Set)

11. Boroscope (One Number)

Annexure-2

SCOPE OF SUPPLY FOR EACH GENERATOR

1.  Generator (Open circuit air cooled) with stator, rotor, built in RTD's, bearings, foundation frame and enclosure for generator with terminals at top.

2.  Brushless excitation system including main exciter (with two slip rings for conventional rotor earth fault relay) and auxiliary Exciter.

3.  Ventilation system for generator with ducting and self cleaning filters.

4.  Phase isolated bus-ducts with aluminum conductor and aluminum enclosure with CT's, PT's, LA & SP cubicles (10 meters on phase side & 6 meters on neutral side).

5.  Neutral grounding transformer with loading resistor.

6.  Conventional Generator control panels and microprocessor based relay panels and duplication of controls in the central control room.

7.  Inter connecting control cables for connection between Generator busduct and C/R panels.

8.  CO2 fire protection for Generator.

9.  Automatic voltage regulator (Digital type).

Annexure-3

EXCLUSIONS

1.  Gas fuel forwarding system including Gas conditioning skid, scrubber (if required), Gas Booster compressor (if required), field piping, fuel measurement, etc.

2.  Liquid fuel system including unloading tanks, centrifuge, forwarding skid, filtering, metering, piping, drain tank and pump, etc.

3.  Instrument air compressor for Gas conditioning skid.

4.  Field piping, valves, etc.

5.  GT exhaust duct & bypass stack with Dampers (Top exhaust stack with silencer of height 15 meters from base line is in scope).

6.  Generator transformer, Generator circuit breaker, Bus ducts beyond specified length.

7.  Auxiliary transformers, starting transformers and breakers.

8.  Field power cables, control and signal cables with cable trays and accessories.

9.  Electrical system studies.

10. All utilities supply systems including cooling water supply system.

11, Water Treatment and Effluent Treatment System.

12. Plant fire protection system (except GTG CO2 fire protection system).

13. Buried earthing.

14. Above ground earthing.

15. Lightning protection materials.

16. Linking of GT Mark V/Generator control panel with any other new/existing system. (Mark V station located in local control cabinet has Modes connectivity for customers remote operation, if any).

17. First fills and consumables (Like Lube oil, Detergent, etc.).

18. Ocean transport, Erection and Commissioning.

19. Obtaining statutory approvals.

20. Power augmentation equipment.

21. Any item not specifically mentioned in the scope but relevant for the project.

Annexure-4

TERMINAL POINTS

1.  Gas at 22.5 Kgf/sqcm, I Micron filtered, 50 deg. C super heated at GT flange (Fuel quality as per GT requirement).

2.  Distillate at 3.0 atg at GT skid, 5 Micron filtered, 17 deg. C super heated above pour point (Fuel quality shall be as per GT requirement).

3.  DM water at water wash skid.

4.  Drains and vents at skid/equipment flanges.

5.  Power (415 VAC/110 VAC & 125 VDC) at GTG skid junction boxes.

6.  6600 Volts power for GT Starting Motor at Motor terminals.

7,  Generator power at l0 meters on phase side bus duet.

8.  Exhaust gas at top of exhaust stack.

9.  Cooling water supply trod return at GT skid.

10. All signal & control cables at GTG skid junction boxes.

Price ………….……. US$23,400,000 each

Availability: March, 2000.

Terms: Will be determined at a later date and is subject to buyers financial strength.

Warranty: Standard Warranty attached to each unit.